Browse Fire Detectors

Detectors - Expert Commentary

Fire Protection For Paper And Pulp Plants
Fire Protection For Paper And Pulp Plants

There is a sense in some markets that the paper and pulp industry will decline owing to the digital technologies with which people interact every day. While this might be considered logical, the reality is completely different. In fact, the paper and pulp industry has experienced a steady growth and will continue to do so in 2021. Production of paper increased by more than 450% in the last decades and the demand of paperboard in the world is expected to grow significantly, driven by e-commerce and big retailers increasing their presence in the online sales universe. This sustained growth in production capacity and paper consumption presents several fire risks to companies and exposes communities that develop around paper mills, to the impact of disasters caused by these fire risks. Fire risks in the paper and pulp industry Paper and cardboard are combustible, but this is not the only fire risk found in these types of industries. Raw materials and finished goods storage are sensitive to fire. In addition, the paper making process includes several stages where fires can occur, due to hot surfaces or poor ventilation. The most relevant fire risks on a paper plant are: Storage Areas: As mentioned before, paper and cardboard are combustible. Solid paper blocks and reels have hard surfaces that don’t ignite easily, but usually these reels can suffer minor damages or have loose sheets that significantly increase the fire risk. When paper reels are stacked in columns, gaps in the center can act as chimneys and when fires start in the bottom of the stack, this chimney effect will accelerate smoke and hot air spread, increasing vertical and horizontal flame spread. Wood and Bale storage fire risks Bale storage also presents a high fire risk, as loose materials are always present Raw materials for the paper making process can have two main sources, forestry products (mainly wood) or recycled cardboard and paper. Wood storage presents several challenges, especially due to wood chips that are highly combustible and, in some cases, even explosive. Bale storage also presents a high fire risk, as loose materials are always present. Fire in baled paper is difficult to extinguish and generates heavy smoke. In many recycling facilities, these paper bales are stored outdoors, where paper or rags soaked in flammable liquids, embedded between the paper sheets, can ignite resulting in a fast spreading fire. Chemicals, flammable liquids and gases In addition, it is possible to find different types of chemicals, flammable liquids and gases that are used in the paper making process. These materials have their own fire-related risks that need to be taken in consideration. Production Areas: In pulp factories, there are several long-distance conveyors that transport wood and wood chips. These conveyors constitute a fire risk and the most probable causes of fire are bearing damage, overheating of the conveyor and igniting chips in the environment. IR dryers, a common source of fire After the wood has been transported, chipped and digested, the paper making process becomes extremely humid, due to the large amounts of hot water and steam needed. But, as soon as the pulp fiber sheet starts to dry, the hot surfaces in contact with the paper sheets can be a source of ignition. IR dryers used in the process are also a common source of fire in the paper industry. When the sheet of paper is formed, close contact with reels and bearings moving fast can create static electricity that could ignite loose paper or airborne particles. Problems like these are likely to be more extensive in tissue mills. Paper dust is generated in certain parts of the process, especially where paper shits are slit or cut. Poorly insulated steam pipes lead to fire Poorly insulated steam pipes can ignite paper dust or even their own insulation materials. In addition, paper dust gathers in the ventilation grills of machinery, causing overheating and igniting as well. Heated oil is used in several parts of the process as well and if a malfunction occurs on the Hot Oil Roll systems, leaks might occur, exposing hot surfaces to this oil and causing ignitions. A paper mill has hydraulically operated machinery, where leaks or sprays might ignite as well. Service Areas: As in many other manufacturing facilities, several service areas can be found. Electrical and network equipment rooms have an inherent fire risk due to damaged wires or equipment, overheating or short circuits in high voltage circuits. Transformer and generator areas entail fire risks as well. High fire risk for boiler rooms Flammable gas distribution systems can be ignition sources, in case of leaks or damaged pipes or valves Hot water and steam are key components for the paper making process. For this reason, paper plants use high capacity boilers that can be powered by flammable liquids or gases. A high fire risk can be considered for boiler rooms. Flammable gas distribution systems can be ignition sources, in case of leaks or damaged pipes or valves. In addition to the fire risks mentioned in these areas, many maintenance operations can also pose fire risk, especially when hot works are being performed. Sparks caused by welding or the use of certain tools can ignite paper sheets or dust in the air. Poor housekeeping and buildup of paper dust, for example, increases the risk associated with maintenance and construction works. Prevention, the first line of defense According to the Health and Safety Executive from the United Kingdom, 60% of fires on paper mills are caused by machine faults and poor housekeeping. The first line of defense to avoid fire risks in paper plants is prevention. As mentioned before, a high number of fires in these types of facilities occur because of poor housekeeping and machine malfunction. The key is to identify the risks and possible ignition sources, and apply measures to minimize them. As in many industries, fire protection has two main components: Passive and Active protection. Passive fire protection measures Passive measures include fire rated walls, ceilings, and floors in the most critical areas. Chemical storage areas should be physically separated from other dangerous areas, if this is not possible then the walls separating areas should be fire rated and materials must be stored in a way that minimizes the risk of fire spread by radiation or conduction. Proper compartmentalization and intumescent protection of structural elements should be part of the package as well. Passive measures include proper ventilation and smoke control. As mentioned before, paper dust is a major fire risk, which is why ventilation and cleaning of hoods over the paper machine is important to minimize the possibility of ignition. Fire resisting construction should be designed with the following goals in mind: Protection of escape routes Form compartments to contain fires that might occur Separate areas of higher fire risk Protect load bearing and structural members to minimize risk of collapse Sprinkler systems, gas extinguishing systems and hose reels Active fire protection includes sprinkler systems, gas extinguishing systems and hose reels to support fire brigades Active fire protection includes sprinkler systems, gas extinguishing systems and hose reels to support fire brigades. Finished goods stored indoors should be protected with sprinkler systems and the same should be considered for chemical storage areas and certain raw materials. Paper bales, ideally should be protected by sprinklers that are suitably designed to cope with the height and located, in all cases, 3 meters above the level of bales stacked vertically (which should not exceed 5 meters height). Spark detectors in hoods, pipes and ventilation systems Dangerous sparks could be generated in several parts of the paper making process, which is why spark detectors must be installed in hoods, pipes, and ventilation systems. Water spray and CO2 systems can be used to protect machinery against these risks. Means to fight fires, like extinguishers and hose reels, should be provided to support fire brigades. All the elements should be properly identified and all personnel should be trained and made aware of the location of such devices. Importance of fire alarms Fire alarms are required in all paper mills and fire alarm call points should be provided in all locations, according to international guidelines, such as NFPA 72 or EN54. The spread of flames and smoke in paper, wood and chemical storage might become extremely fast. For this reason, early detection is critical. Many technologies might be applied in the different areas of a paper plant. Nevertheless, there are dusty or humid areas where regular heat or smoke detectors might fail under certain circumstances. For these areas, especially located outdoors, innovative state-of-the-art detection solutions might be applied, like Video Fire Detection (VFD). NFPA 72 standard for flame and smoke detection NFPA 72 provides guidelines to implement this technology for flame and smoke detection NFPA 72 provides guidelines to implement this technology for flame and smoke detection, opening interesting alternatives for designers and fire protection engineers. Many EHS managers and fire protection professionals selected VFD, because it is the only fire detection solution that effectively covered their needs. Many engineers, specialized in fire protection for paper plants, explained that they tested linear heat detection, aspiration smoke detection, IR/UV detectors and even beams, but none of these technologies performed as they needed on the dirtiest or more humid areas. Video Fire Detection (VFD) solutions Outdoor storage areas are often unprotected, because deploying flame or heat detection in large open areas can be costly and mostly ineffective. VFD solutions can detect smoke and flames in outdoor conditions, allowing the monitoring and protection of wood and paper bales in large areas. Fire detection and alarm systems should be designed with the following goals: Minimize risk of fires, including the use of fire detection technology in areas where regular detection technologies cannot be implemented or are not practical. Minimize risk of flame and smoke spread, with state-of-the-art detection algorithms that guarantee fast and effective detection. Also, reliable algorithms minimize the possibility of nuance or unwanted alarms. In case of a fire, fast detection gives occupants life-saving time to reach to a place of safety, before the flames and smoke have spread to dangerous levels. Global production of paper and pulp reached 490 million tons in 2020, with many industries and markets depended on the paper and pulp supply chain. That is why innovative ways to protect this supply chain, are key to sustain the paper market growth in the future.

The Impact Of The New Safety Bills
The Impact Of The New Safety Bills

Mathew Baxter is the Founder and CEO of the echelon group with responsibility for the management of echelon Consultancy, Pretium Frameworks and echelon Improvement Partnerships. Mathew has spent most of his working life in the construction sector. The devastating Grenfell Tower fire has prompted what the government has referred to as ‘the biggest change in building safety for a generation’. So what do the Building Safety and the Fire Safety Bills mean in terms of emergent legislation and is the housing industry prepared for substantive change on this scale?  Fire Safety Bill Let’s start with the new Fire Safety Bill, which has been designed to give clear definitive guidance principally around areas of responsibility for fire safety. One way of looking at the new Fire Safety Bill is as a piece of legislation designed to beef up the existing legislation, focused specifically around the envelope of the building.   The Fire Safety Bill makes it clear that the person designated as responsible has undertaken a fire safety survey around exterior walls (including cladding, balconies and windows) and individual flat walls entrance doors, where they open onto common parts to make sure they are compliant and if not, then to take any necessary remedial action and precautions to make that building safe. We suspect that demand for fire experts may rapidly outstrip supply. Building Safety Bill The Building Safety Bill proposes a significant amount of consultation is going to be required with residents The Building Safety Bill proposes a significant amount of consultation is going to be required with residents. Every ‘higher risk’ property has to have a strategy around the program of change that it will need. Resident consultation exercises will result in organic documents that will live as long as that building is occupied.  Ideally all stakeholders (for example repairs contractors) coming in and out of properties should be encouraged and trained to take a holistic view of that property, and to be prepared to raise an alert, if they see something that is not right, for example, a fire door that has been propped open.  Checking and replacing old appliances Many fires are caused by residents’ own appliances. Some local authorities are checking tenants’ appliances and if they seem unsafe, either removing or disconnecting them and in some cases, they are also providing free replacements.  Housing associations and landlords will need to demonstrate a comprehensive understanding of their property and stock. For example, if you have a cladded building, you need to know exactly what the specification of that cladding is. Not all cladding is equal and risk profiles vary. Intrusive surveys may be required to ascertain the exact construction and product used. There is still a clear issue that many building owners/managers are unsure of what their building is clad in and how the cladding is fixed for the building. Effectively, this is something landlords need to get a comprehensive understanding of immediately, for fear of very rapid enforcement action from the Local Authority.    Adherence to fire safety regulation compliance Local Authorities are entirely within their rights to approach housing associations and ask for copies of the fire safety regulation compliance of these buildings and if it has not been done then they can take action and that can include decanting the whole building and ordering remedial works As previously mentioned, two new roles are also specified within the Building Safety Bill, that of the Accountable Person within an organization for fire safety and the Building Safety Manager. It is anticipated that the role of the Accountable Person role will need to be fulfilled by a senior member of staff within the client organization and the Building Safety Manager will have a high level of responsibility and accountability for maintaining the safety of the building.  Competency frameworks and resident engagement strategies The Building Safety Bill may have a grace period, before it comes into force on existing buildings The Building Safety Bill may have a grace period, before it comes into force on existing buildings and elements that are likely to be included are already being discussed, for example competency frameworks, resident engagement strategies and two separate roles, namely Building Safety Managers and Accountable Person. One of the most significant changes that the Building Safety Bill will create is a new definition of buildings as ‘higher risk’ buildings. This category will obviously include high rise, but also student accommodation and supported living accommodation.  High risk buildings Any building over 18 meters, or more than six floors high is immediately defined as high risk. The Bill also makes it clear that the new Building Safety Regulator (created under the Bill) can also add other buildings to the category at their discretion. The Bill places a lot more responsibility on landlords and owners of those buildings. In fact, the Accountable Person has legal responsibility for those buildings, as long as they are occupied.  Assessment of fire safety risks Responsibilities include the assessment of fire safety risks, co-operation with any remedial action in terms of fire safety, the registration of high-rise buildings, building safety information and the appointment of the building safety manager.  The Accountable Person has a duty to report the name and details of the Building Safety Manager to the Building Safety Regulator. This individual’s contact details have to be available to everyone in the building, a safety case report has to be undertaken and managed along with a risk assessment and an ongoing strategy for the safety of the building and information provided to the new regulator.  If the Building Safety Manager is found to be non-compliant then she/he risks a prison sentence.  Many of the clients are appointing Building Safety Managers directly with a salary between £60,000 – £70,000. The guidance is that they should not look after more than five buildings each, as the responsibility carries too much weight for more and as such, this represents a significant resource for many landlords with a large portfolio of ‘higher risk’ buildings. Undefined transition period for Act rollout The new Building Safety Regulator will become the Building Control Authority for higher risk building There is expected to be an as yet undefined transition period before the Act applies to existing buildings. As well as the changes that will be necessary to existing buildings, it is essential that consideration is given to the design and thought process behind new developments and new builds. There is a whole new regime for the design and construction phase.  The new Building Safety Regulator will become the Building Control Authority for higher risk buildings. Developers are no longer able to choose their building control authority at will. This imposes strict competency requirements on all duty holders working on higher risk buildings, including the client, the principal designer and principal contractor. Impact of the two safety bills The impact on these two Bills will have an enormous impact on leaseholders and indeed everyone involved in construction and building maintenance. The administrative burden and personal responsibility on those accountable will be equally enormous but, in our view, in the light of Grenfell, absolutely necessary.  Our advice to all our clients is to start planning ahead and to develop a strategy of how they will deliver all the aspects of the Building Safety Bill once it becomes legislation.

How Is Digital Adoption Helping To Improve Fire Safety In Construction?
How Is Digital Adoption Helping To Improve Fire Safety In Construction?

As Grenfell remains a chilling reminder of the importance of fire safety in construction, new digital methods are now being adopted to guarantee the safety of end users. But how is digitization helping and how will this further advance fire safety during the wider construction process? There’s no doubt that the past five years have had a profound effect on the construction industry. Events such as the 2017 Grenfell Tower fire disaster have forced the industry to sit-up and rethink the processes it currently has in place. Campaign for a complete system overhaul The result has been a campaign for a complete system overhaul. Advocates for change, such as Dame Judith Hackitt, are now speaking at length of a ‘broken industry’ and how without major reform, the construction industry will never reach acceptable levels of safety. Yet hope is on the horizon and as is often the case with such events, they can and must serve as a catalyst for major change. Hackitt’s inquiry into building regulations and fire safety, following Grenfell, revealed a need for greater fail safes and a requirement for what Hackitt termed as ‘The Golden Thread’ of information. This is an accurate record of a building, providing a timeline of what has gone into the structure, from design to occupation and its ongoing maintenance. By having this in place, the industry can then deliver full transparency and accountability to help keep end users safe. Introduction of new building safety regulator Hackitt’s inquiry into building regulations and fire safety, following Grenfell, revealed a need for greater fail safesA further response has been the introduction of a new building safety regulator and new construction product regulator, both of which represent a landmark moment not just in fire safety, but improved levels of safety across the board. The first, which is under the Health and Safety Executive, will oversee the safety and performance of all buildings with a new, more stringent framework for higher-risk builds. The latter, (the construction product regulator), will be aimed at manufacturers to ensure that their products are safe, before being sold and that they abide by pre-determined levels of industry safety. If products aren’t deemed fit for purpose, these stricter measures will grant the regulator the power to remove products, revoke building safety certifications, as well as prosecute those who attempt to side-step rules. Building Safety Bill Speaking at the Construction Leaders’ Summit in February 2020, Hackitt explained that the Building Safety Bill and the creation of the new regulators will help the sector to change both technically and culturally, moving away from decisions that result in the ‘cheapest solution’, to one where safety and quality become paramount. Hackitt also warned that the regulators will have real bite. She said, “It will not look to see you have merely followed the rules, but check the building is safe from planning to occupation and you’ve done everything in your power to ensure this.” New laws post building regulations and fire safety review New laws have also been introduced since Hackitt’s review of building regulations and fire safety New laws have also been introduced since Hackitt’s review of building regulations and fire safety. In April of 2020, UK Housing Secretary, Robert Jenrick announced a series of measures comprising of what he called ‘the biggest change in building safety for a generation.’ These were changes that applied to multi-occupancy buildings of 18 meters and above, or six stories, whichever is reached first. For buildings in-scope, a duty holder regime will apply, with a Client, Principal Designer and Principal Contractor. The contractor and designers will have to demonstrate that the building is safe and the ability of the duty-holder to choose which building control body to oversee the removal of the construction/refurbishment. To make sure the regulation is followed, there are gateway points at various stages, requiring regulator sign-off before the project can move forward. The sign-off procedure can then only take place once the right evidence is in place. Before residents are allowed to occupy the building, a full digital documentation will have to be provided which includes drawings and datasets and any design changes will need to be amended, signed-off and recorded. The need for digital adoption It’s clear that with so many changes coming into play that a new way of working is needed, with the needle pointing towards digital adoption as an answer to these issues. One of its main benefits is that it gives specifiers, contractors and residents the ability to access extensive datasets on specific fire related products. This feature plays a huge role in guaranteeing the safety of buildings and end users, by supplying them with the most up-to-date information and the latest in industry laws and regulations. If the industry is to iron-out the risk of products being ‘mis-specified’, then architects must be given a vehicle to access this information as easily as possible. Rise in use of digital tools, 3D and data Another example is the recent changes to the RIBA Plan of Work – the industry blueprint for the process management of a build. While this still remains as the ‘go-to’ map for how a construction process should take place, digital innovation continues to transform many aspects of its project workflow. This can be seen in the likes of ‘Part 3 – Changing Processes’ where the use of digital tools is helping to shift the balance away from 2D information towards 3D and data. Digital site surveys are also becoming the norm, using cloud surveys, photogrammetry, lidar sensors and the ability to mount cameras on drones, to help with the success of projects. BIM (Building Information Modeling) BIM can be used to improve the design, construction and operation of buildings, making them safer for end users Feeding into this is also the greater use of BIM (Building Information Modeling). This digital approach can be used to improve the design, construction and operation of buildings, making them safer for end users. Again, it’s a concept that has been around for some time, but the recent shift in perceptions has allowed this way of working to flourish, with three quarters of specifiers now using BIM, compared to just one in ten a decade ago. Digitization – The only way forward It’s obvious to see that shifting to digital has an immeasurable benefit to the future of the construction industry. Not only do digital tools improve standards, reduce mistakes and improve record keeping and auditing at every stage, but it also keeps costs down and drives up quality. From previous history, we’ve seen that the construction industry is notorious for dragging its heels when it comes to change, but as we’ve seen so far, the quicker it adopts this way of thinking, the quicker improvements in fire safety and compliance can be achieved. ‘Build Back Better’ We’ve heard the government talk of ‘Build Back Better’ and the digitization of the industry will hold all the keys to ensuring this is possible. If nothing else, the construction industry owes it to the victims and survivors of the Grenfell fire tragedy to make sure that all is being done to eradicate the chances of future mistakes from happening again.

Latest MSA Safety Incorporated news

MSA Safety Launches LUNAR Cloud Technology For Firefighter Search And Rescue
MSA Safety Launches LUNAR Cloud Technology For Firefighter Search And Rescue

Over the decades, milestones in firefighter safety technology have included the open-circuit breathing apparatus, flame-resistant fabrics, thermal imaging cameras, and Bluetooth communications. Safety equipment manufacturer, MSA Safety Incorporated announced the availability of LUNAR, a new multi-purpose search, and rescue device that promises to join that list of breakthrough innovations. While production will begin in the coming weeks, LUNAR is available to order now. cloud technology Resulting from years of working directly with Firefighters, LUNAR uses Cloud technology to deliver breakthrough fire-scene management capabilities for incident commanders. According to Nish Vartanian, MSA Chairman, President, and CEO, the introduction of LUNAR delivers on the company’s vision of being a leader in introducing new-to-world technology that protects lives. Fire management “We’ve always viewed LUNAR, and its many potential applications, as a major leap forward and game-changer when it comes to enhancing fire-fighter safety,” Mr. Vartanian said. “Based on firefighter feedback that our team gained through months of LUNAR testing and evaluations with hundreds of firefighters around the world, we believe LUNAR has genuine potential to change the way fires are fought.” Understanding the need Mr. Vartanian added that LUNAR is a great example of how MSA has continued to invest in R&D and technology to advance its vision to protect firefighters from head to toe. “We understand our customers at a deep level. We listen, watch and learn from them. With this knowledge, we then look for ways to use new and advanced technology to help keep them safe, solve their problems and simplify their day.” LUNAR Features Versatile in design, LUNAR can be used as a stand-alone device or as part of an MSA SCBA system. Key features include: Exclusive Firefighting Assisting Search Technology (FAST), which combines distance and direction data enabling firefighters to locate separated teammates faster, when every second counts Personal thermal imaging enhanced with edge detection for improved situational awareness Direct cellular cloud connectivity to send real-time stats, including estimated air pressure, time remaining, and battery life, to Incident Command and remote monitoring personnel for a complete safety point-of-view A unique LUNAR-to-LUNAR network that automatically keeps each device connected to all others on-scene Overcoming challenges According to the National Fire Protection Association (NFPA), there has been a 35% increase in Mayday calls during the COVID pandemic, with more than 40% of Mayday calls never making it to Rescue Teams due to radio communication challenges. Connected Technologies Jason Traynor, MSA’s General Manager of Global Fire Service Products says that LUNAR will help alleviate that burden. “The ability to stay connected to your team can make all the difference during a rescue mission,” Mr. Traynor said. “To be prepared for a day that is more unpredictable than ever, firefighters need advanced tools that can help connect those who are on- and off-scene and support the safety of the entire team with accountability, technology, and data-driven insights. LUNAR will do that and more.” Enhances situational awareness LUNAR is designed for every firefighter on-scene, both on-air and off LUNAR is designed for every firefighter on-scene, both on-air and off, and represents the latest addition to a suite – or ecosystem – of MSA products the company has branded as “Connected Firefighter.” When used together, MSA’s suite of Connected Firefighter products creates greater visibility, increases efficiency, promotes situational awareness, and enables accountability, all while creating an enhanced network of safety. Increased firefighter safety “Accounting for all firefighters on a fire ground has been a consistent need expressed by the fire service profession, but it’s also been a challenge for many manufacturers to solve,” said Mr. Traynor. “When we looked at what we could do to enhance firefighter safety, we used a holistic approach to build a connected ecosystem of products where the sum of the individual components is the key to keeping firefighters better connected – and safer – than ever before.” Connected Firefighter platform Other products comprising MSA’s Connected Firefighter platform include: The company’s industry-leading G1 and M1 SCBA; The MSA HUB, a small, modular device that enables on-scene data and asset management; FireGrid, which gives incident commanders the ability to evaluate and manage multiple situations at one time from any location; and The company’s ALTAIR 4XR and 5X portable multigas detectors with embedded Bluetooth technology provide complete scene management. Responding to Increased Demand Despite the ongoing global pandemic, LUNAR has already generated high interest and demand from across the globe. To respond to this growing need, the company also announced the launch of a live, virtual demo experience that will allow firefighters to learn more about LUNAR from the comfort of their own fire station, at a time that works best for them. Live, virtual demo experience The launch of this immersive, online experience is another example of the company’s ongoing investment in a go-to-market strategy that delivers a unique experience in a way today’s customer expects. “As we continue to deliver on our mission of protecting people at work, I feel we are uniquely positioned to exceed the expectations of those who put their trust in the MSA brand and do so in a way they’ve come to expect from MSA – with speed, agility, and customer-driven innovation,” concluded Mr. Vartanian.

MSA And The National Volunteer Fire Council Partner To Giveaway XF1 Fire Helmet To Three Volunteer Firefighters
MSA And The National Volunteer Fire Council Partner To Giveaway XF1 Fire Helmet To Three Volunteer Firefighters

MSA and the National Volunteer Fire Council (NVFC) are working together to provide the most innovative and up-to-date technology to help first responders improve their health and safety. That’s why three volunteer firefighters that are NVFC members will receive a personalized MSA Cairns® XF1 Fire Helmet in 2021. To be eligible to enter, applicants must be an active U.S. volunteer firefighter and a member of the NVFC. Members will have three opportunities to enter to win an XF1 helmet throughout the year. One recipient will be randomly selected during each entry period. Integrated light module “Many volunteer departments often work with limited budgets, where providing top-of-the-line PPE isn’t an option,” said NVFC chair Steve Hirsch. “We are grateful to MSA for this helmet donation program and their organization’s continuous commitment to the volunteer fire service and the health and safety of our first responders.” The jet-style design of the Cairns® XF1 Fire Helmet reduces snag hazards, provides a personalized fit, and houses its own integrated light module. Plus, the soft goods are removable, washable, and replaceable, helping firefighters align with cancer awareness programs as written by the Firefighter Cancer Support Network. Approvals include NFPA 1971-2018 Structural Firefighting and NFPA 1951-2013 Rescue and Recovery. The first entry period is open now through March 31, 2021.

Fire & Rescue New South Wales Places Second Order For MSA And Pac Fire Australia’s XFlex Range Of Structural PPE
Fire & Rescue New South Wales Places Second Order For MSA And Pac Fire Australia’s XFlex Range Of Structural PPE

Following the successful delivery of more than 5,000 sets of high-quality structural firefighting PPE (Personal Protective Equipment) from globally renowned specialist PPE manufacturer, MSA Bristol (MSA Safety Incorporated) and its Australian distributor, Pac Fire Australia (Pac Fire), Australia’s Fire & Rescue New South Wales (FRNSW) fire service has continued with their roll out and expect to have an additional 5,000 sets of structural PPE delivered by June 2021. The expectation is that Fire & Rescue New South Wales will be able to complete the rollout of structural PPE to all of its 6,500 firefighters by December 2021. Fire & Rescue New South Wales Fire & Rescue New South Wales (FRNSW) is one of the world’s renowned urban fire and rescue services Fire & Rescue New South Wales (FRNSW) is one of the world’s renowned urban fire and rescue services and the busiest fire service in Australia, with more than 6,500 firefighters spread across 335 fire stations and attending close to 120,000 call outs per year. An extensive evaluation and wearer trial carried out in 2019 led to FRNSW selecting MSA Bristol’s popular XFlex ensemble for its PPE (Personal Protective Equipment) upgrade. MSA Bristol is a renowned designer and manufacturer of protective clothing and equipment for emergency services across the globe, formed by the recent acquisition of Bristol Uniforms by MSA Safety Incorporated. XFlex range of structural PPE Its XFlex range of structural PPE has been ergonomically designed with sports styling and lightweight fabrics, providing advanced comfort and protection. The unique fabric combination consists of Safety Components Nomex 360, combined with a GORE PARALLON liner system, which provides unparalleled levels of breathability while preventing drops in thermal protection.  On taking delivery of the new kit, Fire & Rescue New South Wales (FRNSW) Commissioner, Paul Baxter said, “These new uniforms are heavy-duty but lightweight, allowing for enhanced maneuverability and coverage, and will be supplied in a wider range of male and female sizes, so all firefighters will have better fitting garments. They also feature a customized moisture barrier, which helps prevent steam burns and keeps firefighters dry while on the job.” Service information on UHF-RFID chip fitted to PPE Service information, such as garment specifics, is assigned to a unique UHF-RFID chip fitted within the item Pac Fire Australia (Pac Fire) is one of Australasia’s renowned suppliers of personal protective equipment to the fire and emergency industry. Its specialized roll-out of the XFlex range of PPE ensembles to the Fire & Rescue New South Wales has included the allocation of each item to a specific firefighter. Service information, such as garment specifics, date of issue and firefighter information, is assigned to a unique UHF-RFID chip fitted within the item. This process allows garments to interact with inventory management and laundry systems, tracking physical location and the condition of the item, throughout its service life. Advanced fabric technology offers optimum protection Paul Clark, Business Development Manager (BDM) for Pac Fire Australia said, “The XFlex design with its distinctive sports styling has proved particularly popular with the firefighters, offering greater flexibility and reduced resistance when carrying out physical tasks, as well as providing optimum protection thanks to the advanced fabric technology.” Roger Startin, Joint Managing Director at MSA Bristol (MSA Safety Incorporated) said, “The roll-out of the first order went very smoothly, despite the challenges of the global pandemic, and all garments were delivered to schedule. It’s great to see the New South Wales firefighters in action in their new Personal Protective Equipment (PPE) and we’re delighted to be following this up by providing a further 4,500 sets of structural PPE this year.”

vfd