Task force tips XFIH-E21A-A ATEX HURRICANE RC AMER. RED 2.4GHZ ONLY

Technical Specification

Features:
  • Make: Task Force Tips
  • Model code: XFIH-E21A-A
  • Flow Rate (GPM): 1001~1500
  • Inlet Size (in.): 4.0
Additional info:

The Hurricane RC is an electric remote controlled monitor, with a single low-profile waterway discharge. The Hurricane RC has high flow and low friction loss characteristics. Capable of flowing 1250 gpm (4750 l/min) while maintaining a FULL 450° rotational travel (225° either side of center). Maximum operating pressure is 200 psi (14 bar). Field changeable horizontal rotation stops at 45, 90 and 135° either side of center position. Elevation range is 90° above horizontal to 45° below. Designed for 12 VDC or 24 VDC volt operation, selection is automatic. The Hurricane RC comes with a control panel mounted on the monitor for horizontal rotation, elevation, nozzle pattern, programmable PARK and Oscillate. The motor control circuits are factory installed on the monitor and use position encoders and current limiting to protect the drive train at the ends of travel. Unit comes with 30 feet (9m) of ultra-flexing robotics power cable already wired to the monitor, and is enclosed in a unique cable guide that allows FULL 450° of horizontal travel, which is far more reliable than slip rings or coil cords. Knobs for manual override are also provided. TFT’s Master Stream 1250 ER nozzle plugs into the factory installed nozzle power wire. Electric drives and control box are waterproof. Standard outlet is 2.5” NH (64mm) male thread. A built-in automatic drain protects the monitor from freezing. A threaded port 0.25” NPT (6mm) is provided for optional pressure gauge. The monitor is made from hard coat anodized ANSI 356-T6 aluminum and silver powder coat finish inside and out. All TFT RC monitors are capable of being controlled by a programmable logic controller with full three-axis position control & feedback using the Allen Bradley EtherNet/IP protocol. Apparatus - Pumper Certification - ATEX Finish - American Red Horizontal Control - 3" Handwheel Horizontal Movementdegrees - 225 left and right Inlet - 4"ANSI 150 Max Flow - 1,250 gpm (4,500 l/min) Operation Energy Source - 12/24 VDC Oscillation - No Outlet - 2.5"NH Male Remote Control - Yes Valve Design - No Valve Vertical Control - 3" Handwheel Vertical Movementdegrees - -45 to 90 Weight - 43

Read more
Make Task Force Tips
Manufacturer Task Force Tips Inc.
Model code XFIH-E21A-A
Flow Rate (GPM) 1001~1500
Inlet Size (in.) 4.0
Additional info

The Hurricane RC is an electric remote controlled monitor, with a single low-profile waterway discharge. The Hurricane RC has high flow and low friction loss characteristics. Capable of flowing 1250 gpm (4750 l/min) while maintaining a FULL 450° rotational travel (225° either side of center). Maximum operating pressure is 200 psi (14 bar). Field changeable horizontal rotation stops at 45, 90 and 135° either side of center position. Elevation range is 90° above horizontal to 45° below. Designed for 12 VDC or 24 VDC volt operation, selection is automatic. The Hurricane RC comes with a control panel mounted on the monitor for horizontal rotation, elevation, nozzle pattern, programmable PARK and Oscillate. The motor control circuits are factory installed on the monitor and use position encoders and current limiting to protect the drive train at the ends of travel. Unit comes with 30 feet (9m) of ultra-flexing robotics power cable already wired to the monitor, and is enclosed in a unique cable guide that allows FULL 450° of horizontal travel, which is far more reliable than slip rings or coil cords. Knobs for manual override are also provided. TFT’s Master Stream 1250 ER nozzle plugs into the factory installed nozzle power wire. Electric drives and control box are waterproof. Standard outlet is 2.5” NH (64mm) male thread. A built-in automatic drain protects the monitor from freezing. A threaded port 0.25” NPT (6mm) is provided for optional pressure gauge. The monitor is made from hard coat anodized ANSI 356-T6 aluminum and silver powder coat finish inside and out. All TFT RC monitors are capable of being controlled by a programmable logic controller with full three-axis position control & feedback using the Allen Bradley EtherNet/IP protocol.

  • Apparatus - Pumper
  • Certification - ATEX
  • Finish - American Red
  • Horizontal Control - 3" Handwheel
  • Horizontal Movementdegrees - 225 left and right
  • Inlet - 4"ANSI 150
  • Max Flow - 1,250 gpm (4,500 l/min)
  • Operation Energy Source - 12/24 VDC
  • Oscillation - No
  • Outlet - 2.5"NH Male
  • Remote Control - Yes
  • Valve Design - No Valve
  • Vertical Control - 3" Handwheel
  • Vertical Movementdegrees - -45 to 90
  • Weight - 43
Download PDF version Download PDF version
vfd